How To Tune a Car Amplifier For Mids And Highs? In Only 5m

How To Tune a Car Amplifier For Mids And Highs? In Only 5m

Several people are keen to have a good music system in their car. So, they do not think about the expenses, and they should use a quality amplifier for the music system.

Do they have to know how to tune a car amplifier for mids and highs?

From your car speaker powerful audio and hunt of quality will be saved by Boss Audio Systems R1100M.

To purchase a prestigious quality speaker a featured sound will come out from your car speaker, and you can enjoy listening to quality music.

All the information is brought up below. Whether anyone wants to know all the processes they should read them and follow the given method.

Knowing Lows, Mids, And Highs:

First, you have to know about lows, mids, and highs to tune your car amplifier. These are frequencies, where you hear the voice, the mids are, 250hz and 2000hz ranges usually the singer has.

The bass sound is normally low, 500 hz frequencies or low regular lows, which makes an awesome sound like a blast in the car.

Above 2000hz the highs start, which habitually includes a high-key sound on the piano.

Read Also: Making a Car Amplifiers Powerful?

Tune a Car Amplifier For Mids And Highs - Infographics

How To Tune a Car Amplifier For Mids And Highs?

A car amplifier can be tuned very simply for mids and high. Only a few steps have to be applied to set up the system.

Gain Control:

Gain control is installed on the amplifier which is used to match the RCA voltage which runs by cables from the stereo. Several individuals for a volume control knob mistake this.

Mids and highs volume sound will be deformed and clip at a high volume level when the gain control is set up to high.

Nonetheless, all the right and best tools may at home. Thus we suggested that to use your ears and senses.

  1. Let’s any song be played through your car stereo.
  2. Move down the gain on the amplifier, however, not entirely at the back of your car, a little more than halfway down.
  3. The volume should be moved just about to a high level on the stereo and down back it unless any distortion is heard by you from front and back.
  4. Let the gain be slowly increased through a flathead screwdriver after going back to the amplifier. Whether you hear any distortion in the place you have to simply stop the gain increasing immediately.

Turn On The High Pass Filter:

Once the above steps are done, bass and other sounds can toy. You can also check any kind of sound which you like.

If the bass frequencies from the car’s door speaker are needed to block a high pass filter is able to turn on. If the amplifier had switched on that allowed me to flip it on.

To activate the filter the flip switch is needed. Once the filter is activated from 80hz to 200hz can be adjusted anywhere. You are suggested to set your high pass filter to no more than 80hz. Below that anything can be handled by a subwoofer.

After that, you have to set a low pass filter. Only the bass is played by a low pass filter and is able to be set to lower than 80hz.

Consider Facts While Tuning A Car Amplifier:

Here are some the most important facts that you need to consider while tuning your car amp:

Setting Gain Correctly:

A car audio experience can be entirely caused by turning the wrong level on a gain setting which is necessarily noisy.

Thus, make clear the gain setting is correctly turned. So that speakers are able to perform correctly too.

Types Of Amplifiers:

While adjusting the amplifier, you are suggested to think about the kind of amplifier to assist you to maximize the output you have to buy the prestigious feature and read its manual.

Speakers Power:

While turning an amplifier, the additional advantage is to have a powerful speaker. The power output is increased from an amplifier and thus enjoying music is allowed.

Connectivity Of Cables:

You are suggested to use the best cables. Furthermore, you should use and test the Boos Audio Systems Car amplifier and also the 8 gauge wiring kit which has a speaker wire, powerful cables, ground cable, etc.

I suggest it for a long-term solution to your amplifier connectivity solution.

Read Also: How To Test A Car Amplifier With A Multimeter? In Just 5m

Car Amps Types and Uses - Infographics

Frequently Asked Questions

Let’s take a look at some related questions asked by every person.

Q. How do I know if my car speaker wire is working?

Connect the end of the car speaker wire to the battery. If the sound is heard it means a good sign.

If not make clear that everything is verified and connected properly. And then with another wire try it again.

Q. Which is the most powerful car speaker?

There are many powerful speakers, but I would like to recommend Coaxial Car Stereo Speakers Pioneer 6-1/2″ G-Series.

It is best for high-quality output to sound in the full range and stereo audio output categories belong. 300 watts is the peak power of each speaker.

Q. What size amp do I need for Mids and Highs?

You can go with a 5-channel or 4-channel amplifier and a Monoblock if you have 4 speakers and a subwoofer. For the mids and highs, the 4-channel is the best amplifier.

Q. How much does it cost to tune an amplifier with mids and highs?

The cost depends on the amplifier and speaker and moreover on the source. If you do it by yourself then it will not cost much.

What is the best frequency for mids and highs – car amp?

For car amplifier mids, aim for a crossover frequency of around 80 Hz to 120 Hz.

For highs (tweeters), a crossover point of 2,000 Hz to 4,000 Hz is common. Adjust to suit your specific speakers and preferences.


The method that is brought up above using it will give you a good sound. There is no need to use a technical tool while tuning a car amplifier with mids and highs.

You have to read all the information and do it the same as is mentioned. You are able to do it simply with a few steps. You have just to go through the process.

Have a nice day and thanks for reading along!


Similar Posts